LogHX: English version

[RX4HX]

Telnet kept disconnecting

Yes, here is some proplem! Pse QRX!

[M0CGF]

Hi had the vhfstpete dll flagged today and also telnet disconnects.

However I have an issue with the bandmap, its just not showing even though its ticked.

I have recently changed to a new win11 PC from win10, and I am not sure if my install copied across OK as each time i load it I have various different things happening. It doesn't seen to save the views and associated radios.

Question for everyone incase there is a better way.

I have a view for SSB where I have a radio selected for control.

For FT8 I have a view with wsjtx loaded, in Loghx no radio is selected and its controlled via wsjtx.

Best way to manage it? Issue is if I want to quickly nip to ssb then its a reload of view as the reports are still +- etc.

- - - Добавлено - - -

ignore this I managed to fix the view by copying over the ini for the bandmap from a different view.

[Jim Smith]

I'm still getting the telnet disconnects as well.. only to localhost - external ones are fine.

Also sone UI issues..

Firstly, on loading LogHX, I get the following 2 error windows:






After loading, there are 2 windows that don't come up properly...

First the Awards window - all font sizes increase by approx 35% each time the window is reopened.

Secondly, the Frequency window. I have set it to look like this:



but after reloading the software, it comes up like this:



I have to re-set it each time.

Even though I have saved the setup under "Select View" once I have it as I want, the issues still persist.

It's worth pointing out that I have a multi-screen setup here, I don't know if that is part of the problem.

[RX4HX]

on loading LogHX, I get the following 2 error windows

Log version?

the Frequency window. I have set it to look like this:

It's not good. I'll check it out.

[Jim Smith]

[QUOTE=RX4HX;2075109]Log version?



Oh sorry ! Should have said.... Build 776

[M0CGF]

since updating my gfx card all the views open but they seem to all appear off the screen and I cannot view the windows. REally weird.

Is there anything I can reset in the view ini to fix this?

[Jim Smith]

since updating my gfx card all the views open but they seem to all appear off the screen and I cannot view the windows. REally weird.

Is there anything I can reset in the view ini to fix this?

While we wait and see if Alexei comes up with a solution....

I don't have a definitive answer, but the file you're looking for is likely to be in LogHX/INI/Vews/GeneralViews then select the folder of the name of the view you are currently using. Make a copy of the loghx_view.ini, so that if this doesnt work, you still have a copy of the original.

Change all lines starting "left" or "top" to 0 and see if that repositions your windows to where you can see them on restarting LogHX.

I THINK that worked for me in the past.

[RX4HX]

since updating my gfx card all the views open but they seem to all appear off the screen and I cannot view the windows. REally weird.

Do you use 2 monitors? If yes, change in Windows setup main monitor.
Or - Shift+menu for window = open window in Left=0, Top=0.
Or -

Change all lines starting "left" or "top" to 0

[M0CGF]

Thanks will try it.

One more question.

I have view for SSB and a view for FT8. I am sure before this reinstall that the SSB allowed a radio in CATHX and in FT8 view the radio was disabled. I've tried resaving the views with these settings but the radio still remains on and clashes with wsjtx for control and the radio ends up in rtty-r mode.

[RX4HX]

I have view for SSB and a view for FT8. I am sure before this reinstall that the SSB allowed a radio in CATHX and in FT8 view the radio was disabled.

Do you want link CAT to View? If yes, check here -